Pacific Northwest Four Wheel Drive Association

Pacific Northwest Four Wheel Drive Association (
-   Swapmeet (
-   -   jeep cherokee parts (

cda78cj 08-29-2011 08:52 PM

jeep cherokee parts
Ok this is kinda a poll, A buddy and I are finally all set up for fabbing and are building a variety of things for our cherokees and buddy's ford ranger, such as
front winch bumper, xj and ranger
rear bumper with tire swingout and jerry can holder
rock sliders with mounts (weld on)
tube doors front and rear, for ranger also
hoops from xj front bumper to rock sliders
hoops from xj rear bumper to rock sliders
ford ranger flat bed kit
rear xj quarter pannel guards

so my question is who if anyone would be interested in any of these items?
our goal is to make quality products for a lot less then the crap on ebay and out of the catalog but hold up to a good beating like my little beast gets, and we are local so you wont be paying a Fq&* TON on shipping lol.
All tubing will be hrew(non structuarl things) and DOM for the rest, all mounts to frame from bumpers 1/4'', use of a tube bender not a pipe bender.

As interest rises and projects complete I will post pics. Thanks all!

cda78cj 09-09-2011 06:56 AM

So as it stands now a basic front bumper with winch mount and light tabs $250 will have pics up soon of first completion. Working on rear bumper with jerry can holder and spare tire swingout rough estimate is 550-650 depending on materials.

jim putman 09-09-2011 09:08 AM

It would be great if someone was to make some body armor similar to gen rite for jeeps. (particularly CJs and flatfenders) I would have bought a set for my flatty but the shipping is a killer

Magical_Merlin 09-09-2011 09:49 AM

I have some fab needs. What is your contact info? Im in Puyallup and it would be great to have a go to fab shop near by.

cda78cj 09-09-2011 01:19 PM

Well let us know what you need, measurements and ideas of what you want. contact info or call 253-720-6513 for serious inquiries only please. There is only two of us and once we have proper measurements and solid idea of what you are after we will bust our tails to get it done in a timely mannor.

The rock sliders we build are either hrew or DOM depending which you want and come with mounting hardware pre notched and all you need to do is tack in place and weld up or for a small fee we can mount em for you.

cda78cj 09-10-2011 10:48 PM

4 Attachment(s)
Here is the first front bumper, not 100% done, this is for my partner and his xj has a 4.3 with aluminum radiator so we are cuting the mounts to add a skidplate. the sides will be cut and capped.

Stinger can be added, also hoops to follow fender to tie into rock sliders if wanted.

Also here is a few early pics of the rear using same 4 bolt holes as oem, similar to others you may see if doubting integrity of strength. Still working on tire carrier and jerry can mount. Ends will be capped, still leaves room for tow hitch underneath in original mounted position.

We can add backup flood lights installed into bumper with pigtail ready for you to connect.
Also the rear tire carrier
And lastly jerry can mount
As well as hoops to tie into sliders

cda78cj 10-03-2011 05:55 PM

As for those rear corner guards it wouldnt be much of a price break except minus the shipping since we are local but the cost of steel is what gets the prices up there.

Also I just recently baught a 89comanche and will be exo caging the bed so it stays in tact when wheeling and swapping all my xj parts I can over to it.

82datsun720 11-28-2011 12:01 PM

hey you still fabbing jeep parts over in puyallup? I live in puyallup and am having a hard time finding steel, any words of advice would be greatly appreciated. I am from Texas so dont know the area to well.

cda78cj 11-28-2011 08:50 PM

sure am, working on rock sliders for MJ, rear tube bumper for it as well. We get out metal from Interwest metals down in fife, also I hear somewhere downtown puyallup is another place off east main st

82datsun720 11-28-2011 11:31 PM

that rear bumper on the XJ in this thread looks awesome. that is the look of the front bumper i am going with. yall keep up the great work, and thanks for the lead on steel... ill check out the place on East main if i can find it, and give you a heads up on the steel prices.

All times are GMT -7. The time now is 08:46 PM.

Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.